Basic RF Terminology

This page covers basic RF terminology useful for rf design,development and testing. It covers RF terms which include power,relation between dBm and dBw, VSWR,Gain, Return Loss, relation between VSWR and Return loss,Insertion Loss, Reflection coefficient,harmonics,spurious,phase noise,group delay, frequency stability both short term and long term,1dB compression point(P1dB), 3rd order intercept point(TOI),LNB(Low Noise Block converter), BUC(Block Up Converter), Sensitivity, AM-AM conversion,AM-PM conversion, EMI,EMC,Susceptibility and more.

Power: It is usually measurement of IF signal and RF signal, which is expressed in dBm or dBW. Power levels at IF output of a modem will be usually lower and typically fall in the range from -20dBm to 0dBm. Power levels at SSPA or HPA usually higher and typically fall around 20 to 40W and sometimes 50-100W and hence measured in dBW.
dBm is the ratio (in dB) of power relative to 1 mW,
dBm =10*Log (P), where P is power in mW.
dBW is the ratio (in dB) of power relative to 1W.
dBW =10*Log (P), where P is power in watts.
0dBW=+30dBm

VSWR: Stands for Voltage Standing Wave Ratio and is a measure of the accuracy of impedance matching at a point of connection. It is expressed as a ratio e.g. 1.3:1. VSWR is usually used at microwave frequencies. Return Loss is most commonly used at IF frequencies.
RL=20*Log (VSWR+1/VSWR-1)

Gain: It is expressed in dB and is ratio of output power of an amplifier device to the input power.

Return Loss: Function is similar to VSWR but expressed in dB.

Insertion Loss: It is expressed in dB and is ratio of output power of an attenuating device to the input power.

Reflection coefficient: It is the ratio of reflected wave to incident wave at point of reflection on transmission line. This value varies from -1 (for short load) to +1 (for open load), and becomes 0 for matched impedance load.
Reflection coefficient(r) = (Zn - 1)/ (Zn + 1),
Where Zn = Z/Z0
Zn = normalized load impedance
Z0 = characteristic impedance of line (Ohm)
Z = load impedance (Ohm)

Harmonics: All frequency converters and signal sources produce frequencies at integer multiples of input frequencies, which are called harmonics.

Spurious: All frequency converters and signal sources produce frequencies at non-integer multiples of input frequencies, which are called spurious.

Phase Noise: It is measured in frequency domain and is expressed as a ratio of signal power to noise power measured in a 1Hz Bandwidth at a given offset from the desired signal.

Group Delay: Delay for the signal to transit from input to output for Device under Test (DUT). This is caused due to reactive elements used within the device. It is proportional to the change in slope of the phase shift response versus frequency curve. For example +/-2ns from 824 to 835 MHz

Frequency stability: It is the change in frequency of the Local oscillators, frequency converters and synthesizers mainly due to aging and temperature. They are two types short term and long term and measured in PPM/day or PPM/year respectively.
PPM: Parts per million, usually used to express frequency stability of Local oscillators.

1dB compression point: The 1dB Gain Compression point is the output power at which the input/output transfer response of an SSPA departs from a straight line by 1dB. Higher it is good for the system.

3rd order intercept point: It is a measure of linearity which describes the amount of third order harmonic that can be expressed in a device. It is referred to the input and output of a module.
TOI in dBm = (Input signal levels in dBm) + (distortion products (dBc)/2)

P1dB versus TOI

Refer following links to know more on P1dB versus TOI, 2nd order Intercept point vs 3rd order Intercept point.
P1dB vs TOI   second order intercept point vs third order intercept point

LNB: It is used as abbreviation for Low Noise Block converter, which is combination of LNA and Down converter.
For more on Low noise block converter refer page on LNB.

BUC: It is used as abbreviation for Block Up Converter, which is combination of Up converter and Power Amplifier.
For more on Block Up Converter refer page on BUC.

Sensitivity: Measured in receiver. Sensitivity in a receiver is normally taken as the minimum input signal (Smin) required to produce a specified output signal having a specified signal-to-noise (S/N) ratio and is defined as the minimum signal-to-noise ratio times the mean noise power
Smin= (S/N) min *k *To *B *(NF)

AM-AM conversion: AM-to-AM conversion measures the amount of undesired amplitude deviation (AM) that is caused by amplitude variations (AM) of the system. It is a critical parameter in systems where amplitude modulation is used, such as QAM. Un-intentional amplitude variations (AM) are caused due to Power supply ripple, Thermal drift and Multipath fading.
For more on AM-AM conversion, refer our page on AM-AM conversion.

AM-PM conversion: AM-to-PM conversion measures the amount of undesired phase deviation (PM) that is caused by amplitude variations (AM) of the system. AM-to-PM conversion is a critical parameter in systems where phase (angular) modulation is used, such as FM, QPSK and 16QAM. AM-to-PM conversion is usually defined as the change in output phase for a 1-dB increment in the power-sweep applied to the amplifier's input.
For more on AM-PM conversion,refer our page on AM-PM conversion.

EMI: Extend to which one device radiated field influences the proper functioning of another device. It is caused by undesirable radiated electromagnetic fields or conducted voltages or currents.

EMC: Extend to which electrical appliances can withstand each others radiated fields. The goal of EMC is to minimize the influence of electric noise.

For More on EMI/EMC basics,EMI/EMC measurements,EMI/EMC shielding materials,enclosure,test equipment vendors refer our page on EMI EMC.

Susceptibility: The inability of equipment/systems to perform without degradation in the presence of an electro-magnetic disturbance. The threshold of susceptibility is the level of interference at which the DUT begins to show degradation in performance. This is often frequency dependent.

RELATED LINKS

RF converter design
C band RF Transceiver basics
RF filter design
RF vector Signal generation/analysis
Microstrip line basics
RF and SoC Testing
rf connector
Rectangular Waveguide
RF Terminologies
what is RF
RF circulator basics
RF isolator basics
RF Power Amplifier

Other useful Terminologies

WiMAX TERMINOLOGY
GSM TERMINOLOGY
LTE TERMINOLOGY
SATELLITE TERMINOLOGY
RF TERMINOLOGY

RF and Wireless Terminologies